Tycho Solutions handles ac installation in Phoenix, AZ, on new construction and whole-system replacement. Sized to the house, installed complete, never patched.
Phoenix attics push past 140 to 150 degrees at the roof deck through July and August, and every foot of ductwork and refrigerant line routed through there fights that heat before conditioned air reaches a register. Homes from the 1960s through 1980s ranch era typically carry undersized tonnage and duct wrap baked brittle, so the system runs long and still can’t hold setpoint on the worst afternoons.
Newer two story stucco homes moved duct into conditioned space, which helps, but the original design rarely planned for it, so static pressure problems surface later. Either way, setting a new unit on old, leaking ductwork repeats the failure. Replacement means resizing the load, sealing the duct path, and charging refrigerant for the equipment actually installed.
From new home builds to full system replacements, our Phoenix AC installation crews size, engineer, and install cooling equipment that holds up through triple digit summers.
We size every system to the actual heat load of your home or building, then seal and insulate the ductwork carrying it.
Central Phoenix sits at low desert elevation with summer highs that push cooling equipment to its limit. We size and install new AC systems for that heat load, whether the job is a new build or a full replacement of an outdated condenser.
Phoenix winters are mild, so furnaces here are almost always installed as part of a paired heating and cooling system, not a standalone unit. We install new gas furnaces sized to the home and integrated with the ductwork during new construction or a full system upgrade.
Room additions, converted garages, and casitas are common in Phoenix, and running new main ductwork into them isn’t always practical. We install ductless mini split systems sized for the individual space, giving it independent cooling and heating without disturbing the home’s existing system.
New construction across Phoenix ranges from single custom homes to larger multi-family and commercial projects, each needing a complete HVAC system designed from the ground up. We handle full system installation, from equipment selection through ductwork and startup, coordinated to the build schedule.
Arizona’s mild winters and long cooling season make heat pumps a practical fit for new Phoenix homes, since one system handles both sides of the year. We install new heat pump systems sized to the home’s load, giving builders a single piece of equipment instead of two.
Phoenix attics run far hotter than the outside air during summer, so how a duct system is built and sealed determines how much of that heat reaches the living space. We fabricate and install new duct systems sized for each room, sealing every joint and connection before insulation goes in.
Builders bring us in during framing so ductwork gets planned before drywall closes the chase, and homeowners call us when a system finally gives out after fifteen or twenty summers. Either way, the job is engineered for the load, not guessed at from the old unit’s nameplate.
New systems in Phoenix ship with a manufacturer backed warranty and our own written workmanship warranty on the install.
One team manages permitting, inspection scheduling, and equipment delivery so your Phoenix installation stays on the builder’s timeline.
We install equipment sized to Phoenix heat loads with sealed, insulated ductwork built for triple digit attic temperatures.
Phoenix’s housing stock spans 1950s ranch infill near the core, 1970s and 1980s single story tract homes across the east and west valleys, and newer two story stucco production building on the outer edges. Slab on grade construction is standard throughout, so there’s no basement for mechanical space. Every duct run, air handler, and refrigerant line lives in the attic or a closet, directly under the hottest part of the house.
The failure point is rarely the compressor first. It’s the duct system: flex duct crushed in a low attic, connections sealed with cloth back tape that’s dried out and let go, and return air never sized to match the supply. That imbalance pulls hot attic air through every gap in the ceiling plane, so the system fights infiltration heat on top of the load it was already sized for. Replacing the condenser alone just repeats the failure.
Most Phoenix subdivisions carry HOA rules on condenser placement, screening walls, and visible line sets, especially on corner lots and anything facing a street or common area. New construction and full replacements both need equipment sited and screened before permitting, which is why we coordinate placement with the builder or homeowner up front instead of defaulting to wherever the old pad sits.
By submitting this form, you agree to receive communications from Tycho Solutions. We respect your privacy.
Every Phoenix HVAC installation runs under Arizona ROC #364735, fully licensed, bonded, and insured for residential and commercial work.
New equipment carries a manufacturer warranty plus our own written workmanship warranty on every install.
We work directly with Phoenix builders on framing, permits, and inspections so HVAC installs stay on schedule.
Phoenix installs are scheduled and staffed to finish on the timeline and price we quote, no surprises.
Cost depends on tonnage, ductwork condition, and whether it’s a straight swap or a full system built around new load calculations. A unit that looks similar to your old one on paper can end up costing more once undersized returns, leaky duct, or code required upgrades like a disconnect or pad get factored in.
We walk every Phoenix homeowner through a real load calculation and a written quote before any work starts, so there’s no guessing once the crew shows up.
We’re an installation and replacement company, not a repair shop, because a patched compressor or a recharged line set on an aging system usually fails again within a season or two once the rest of the equipment is working that hard.
If your system is past the ten to fifteen year mark, or a repair estimate is creeping toward a meaningful fraction of what a new system costs, replacement is almost always the better move in Phoenix’s climate.
Yes. Flat and low slope roofs, common on Phoenix commercial buildings and some contemporary homes, take packaged rooftop units set on a curb instead of a split system with a ground level condenser.
That means proper curb flashing, condensate drainage that won’t pond on the membrane, and a walkway pad for service access. We size and set the curb before the unit ever arrives so the roof penetration is sealed correctly the first time, not patched around afterward.
Yes, commercial HVAC installation in Phoenix is a regular part of our work, from single tenant retail buildouts to multi-unit and light industrial projects.
We size rooftop package units and ducted systems to the building’s actual occupancy and equipment load, coordinate with the general contractor’s schedule, and pull the mechanical permits required for commercial work in Maricopa County. It’s a full system installed to code, not a residential unit scaled up.
Yes. New construction HVAC in Phoenix works best when we’re brought in during framing, before insulation and drywall close up the chase for ductwork and refrigerant lines.
We run the load calculation off the actual plans, size supply and return runs before the attic gets hot to work in, and coordinate rough in and final connection around the builder’s schedule. Waiting until move in to size the system means guessing at a load the house hasn’t been tested against yet.
Yes, a full system installation needs a mechanical permit and inspection, whether it’s a straight replacement or new construction. We pull permits under Arizona ROC #364735 and schedule the inspection as part of the job, so it’s built into the timeline rather than an extra step you have to chase down afterward.
Skipping the permit on a full swap can also create a problem later at resale, when a lender or buyer’s inspector asks for it.
