Tycho Solutions provides hvac installation for new construction, full system replacement, and commercial buildout across the Valley, from single family homes to multi building developments. Every project starts with a load calculation, not a guess, so the system you get matches the structure you built.
Building a new home or upgrading an aging property calls for careful planning. New construction hvac installation in Arizona determines your comfort for decades, since retrofitting undersized ductwork after drywall goes up means cutting into finished walls and ceilings. We size equipment against Manual J load calculations, not square footage rules of thumb, factoring in insulation R-value, window orientation, and roof pitch before a single duct run gets fabricated.
Our team works directly with homeowners, builders, and general contractors across the Valley to engineer customized hvac solutions. From calculating proper tonnage for a large custom build to zoning a two story home so upstairs bedrooms are not fighting the downstairs great room for airflow, every system is designed around how the building was actually constructed, not a generic spec sheet.
Specializing in complete system installations, not small parts swaps
Licensed General Contractor
Precision HVAC Installation for Long Term Performance
Complete hvac system installation for custom homes, planned from the framing stage forward. We integrate cooling infrastructure directly into your architectural plans before drywall closes up the walls, coordinating with your framer and electrician so plenums, chases, and condenser pads land exactly where the blueprints call for them.
Full replacement of outdated units with high efficiency modern systems. SEER rating, unit size, and existing ductwork condition all factor into hvac installation cost, and a unit that is oversized for the space will short cycle and leave humidity behind no matter how high its rating looks on paper.
Fabrication and installation of new duct systems. Proper sizing and sealing ensure airflow reaches every room efficiently, without the pressure loss that comes from crushed flex duct or undersized trunk lines. We seal every joint with mastic, not just tape, since tape fails within a few summers under attic heat.
A heat pump delivers both heating and cooling from a single outdoor unit, ideal for energy efficient Arizona homes that run cooling nine months out of the year and only need supplemental heat on the coldest winter nights. Because it moves heat instead of generating it, a heat pump often costs less to operate than a straight electric furnace paired with a separate air conditioner.
Ductless mini split installation for room additions, casitas, or garages. Targeted cooling without extending main ductwork through finished walls or ceilings, using a small refrigerant line set that runs through a compact wall penetration instead of a full duct run.
Large scale hvac system installation cost for commercial properties depends on square footage, zoning needs, and rooftop access, and we scope each project against the building’s actual mechanical drawings rather than a flat per square foot number. Rooftop units on a flat commercial roof need curb adapters matched to the existing structural penetrations, and we coordinate that work with your general contractor and roofing crew so nothing gets cut twice.
We do not guess. We perform detailed Manual J, D, and S calculations to ensure every system is perfectly sized for the home’s square footage, insulation values, and window orientation, because an oversized unit cycles too fast to pull humidity out of the air and an undersized one runs constantly without ever catching up on a 110 degree afternoon.
We understand construction timelines. Our teams arrive when scheduled, complete rough ins and trim outs efficiently, and never hold up the next trade waiting on inspection sign off, since a stalled HVAC rough in can push drywall, insulation, and paint back by a full week on a tight build schedule.
Our work meets or exceeds all applicable building codes. We handle the permitting process and ensure our installations pass inspection the first time, so you are never waiting on a re-inspection to close out a phase.
We install industry leading brands known for durability in high heat environments, chosen for compressors and coils that hold up to a full Arizona cooling season without breaking down.
Sizing depends on more than just square footage. We consider ceiling height, window placement, insulation quality, and sun exposure. We perform a Manual J load calculation for every project so the equipment matches the actual structure, not a rule of thumb tonnage guess.
Yes. All new equipment comes with full manufacturer warranties, typically 10 years on parts. Additionally, Tycho Solutions provides a labor warranty on our installation work, so if something related to our installation needs attention, you are covered beyond the manufacturer’s terms.
Absolutely. Ductless mini splits are an excellent option for casitas, garages, or home offices where running ductwork would be impractical. We can design a single zone or multi zone system depending on how many separate spaces need independent temperature control.
Most residential replacements are completed in one day. For new construction, the timeline is split between the rough in phase, running ductwork and refrigerant lines before drywall goes up, and the trim out phase, setting equipment and connecting controls once the home is closer to finished.
Contact us today for a consultation on your new construction or replacement HVAC installation.
