Tycho Solutions handles ac installation in Chandler, AZ, on new construction and whole-system replacement. Sized to the house, installed complete, never patched.
Chandler’s housing stock splits mostly between 1980s and 1990s single story homes with long attic duct runs and newer construction built after 2005 with tighter, better sealed attics. Either way, attic temperatures here routinely climb past 140 degrees in July and August, and any HVAC system has to move air through that heat for months at a time, not just on the hottest afternoon.
A load calculation done for average Arizona conditions ten years ago does not hold up against Chandler’s current summer highs. We size every installation, AC, furnace, heat pump, or full system, to the actual house and duct run in front of us, then check whether the existing ductwork can carry what the new equipment delivers.
Chandler summers push AC systems past their limits for months at a time, so every install here starts with a load calculation built for that heat, not a generic swap.
We size every Chandler installation for real attic and rooftop heat loads, not a generic replacement swap.
New AC installation for a Chandler property starts with a load calculation sized to summer highs past 115 degrees, then correct equipment placement, refrigerant line set, condenser pad, and electrical tie in. We commission and test the system before handoff, whether it’s a remodel or a new build.
Chandler homes run furnaces only a handful of cool weeks each year, so we install a properly matched gas or electric furnace paired to your new AC system rather than an oversized unit. Ductwork, venting, and thermostat wiring are set up during the same visit for a coordinated system.
Ductless mini split installation for a garage conversion, casita, or room addition that the main system wasn’t built to cool. We run the line set and mount the indoor and outdoor units without opening up existing ductwork, so the rest of the Chandler home stays untouched.
Complete HVAC system installation for new construction and full replacements across Chandler, from Manual J load calculations through equipment selection, ductwork layout, and startup. We coordinate with builders and other trades on scheduling so the system goes in on the framing and trim timeline, not after it.
Heat pump installation gives a Chandler home one system for both heating and cooling instead of a separate furnace, which suits smaller lots and homes where equipment space is limited. We size the unit to the home’s square footage and set it up to meet current SEER2 requirements.
New ductwork fabrication and installation sized and sealed to move air efficiently through Arizona attic heat, which is where most duct runs lose performance. We build and install the duct system to reach every room, whether we’re roughing it in during framing or replacing an undersized layout.
Builders and homeowners across Chandler choose Tycho because every installation starts with a load calculation for this heat, not a catalog swap. Licensed under ROC #364735, we plan equipment placement, refrigerant lines, and ductwork together, so the system is sized once and works the first summer.
Every new system carries manufacturer and workmanship coverage, which matters in Chandler where compressors run nearly nine months a year.
One crew manages load calculation, equipment, ductwork, and startup on your Chandler project, so nothing gets handed off between trades.
We install equipment sized to Chandler’s summer highs and sealed ductwork rated for attic heat, not builder grade minimums.
Chandler grew fast from the mid 1980s through the 2000s, and most of that stock is single story stucco construction with concrete tile or shingle roofs and long attic duct runs tucked above thin attic insulation. Homes built before the mid 1990s often still carry original ductwork and undersized returns sized for summer design temperatures lower than what we see now.
The failure point is rarely the compressor itself. It’s the duct system baking in attic space that regularly tops 140 degrees for months, where flex duct insulation compresses, mastic joints dry out, and return air gets pulled from a superheated attic instead of the conditioned space. A new condenser bolted onto that same ductwork runs harder and shorter than the old one did, which is why we treat the duct system as part of the installation, not an afterthought.
Design guidelines in Chandler’s newer developments commonly restrict condenser placement, equipment screening, and exposed refrigerant line sets on street facing walls, and older tracts leave tighter side yards for equipment than newer lots do. We plan location and routing against those rules before we order equipment, and size ductwork and returns to the actual floor plan rather than a template pulled from an older permit.
By submitting this form, you agree to receive communications from Tycho Solutions. We respect your privacy.
Tycho Solutions is licensed, bonded, and insured for HVAC work in Arizona under ROC #364735.
The same crew handles load calculation, equipment, ductwork, and startup on your Chandler installation.
Every system is sized to Chandler’s actual summer highs, not a nameplate swap from the old unit.
We schedule Chandler installations around your household or jobsite, with a clear timeline set before work begins.
Cost depends on the tonnage the load calculation calls for, the condition of your existing ductwork, and whether the job is a straight swap or includes new duct runs, a bigger return, or electrical work for a larger unit. A system going into a home with sound ductwork costs less than one that also needs the duct system rebuilt.
We run the load calculation and give a written number before ordering equipment, so there’s no guessing once the crew is on site.
Once a compressor or coil fails on a system already past ten to twelve years old, a repair usually buys a few more months before the next component goes, not a real fix. We focus on new AC installation and full system replacement rather than patch repairs, because a mismatched repair part on an aging system usually just delays the same failure into next summer’s heat.
If something major just went on a system that age, we’ll walk you through why replacement is the more honest call.
Yes. Flat and low-slope roofs, common on Chandler garages, additions, and commercial buildings, usually call for a rooftop package unit set on a curb rather than a split system with a ground level condenser. We check the roof structure and existing curb before sizing equipment, seal the curb and duct penetrations correctly for our sun exposure, and route condensate so it drains off the roof instead of pooling against the membrane.
Yes. Commercial HVAC installation in Chandler covers everything from a single rooftop package unit on a small retail space to multi-unit systems and full ductwork layouts for a new building. We size equipment to the actual occupancy and equipment load rather than a rule of thumb, and we coordinate installation around your hours so the space stays usable.
Tycho Solutions holds Arizona ROC #364735, and we pull the mechanical permit ourselves on every job, whether it’s a straight replacement or a new construction hvac in Chandler build. The permit triggers an inspection on the finished work, which is your proof the installation was done to code, not just to the manufacturer’s minimum, and it protects you if the system is ever inspected during a sale.
A straight system swap on existing ductwork that’s in good shape usually takes one day. A full replacement that includes new ductwork, a heat pump conversion, or work tied to new construction runs longer, typically two to four days depending on attic access and how much duct needs to be replaced. We schedule around Chandler’s heat, working attic space early in the day whenever possible.
