Tycho Solutions handles spray foam insulation in Tempe, AZ, on new builds and retrofits. Complete envelopes specified to the assembly, not topped up.
Tempe’s older neighborhoods near ASU, built through the 1960s to 1980s, still run original fiberglass batts settled to a few inches under decades of attic dust and foot traffic, well short of current code depth. Flat and low-slope roofs common on these blocks soak up direct desert sun with minimal attic ventilation, pushing attic air well past 140 degrees.
Newer construction across Tempe’s east side tract developments meets current energy code with full-depth batts or blown-in cellulose at the build stage, but tile roofing common on these roofs traps radiant heat in the tile field itself. Any addition, garage conversion, or attic rebuild is the right point to bring insulation up to full depth instead of working around what’s already there.
We size every attic and wall system to Tempe’s heat load, matching material and depth to the roof and framing already in place.
From ASU-era bungalows to new master-planned construction, Tycho Solutions installs spray foam, attic, batt, and blown in insulation built to perform against Tempe’s desert heat load.
In Tempe’s additions and new builds, we apply open and closed cell spray foam to roof decking and wall cavities as the structure goes up. The air tight seal cuts heat transfer through Tempe’s long cooling season and fills the irregular attic shapes common in older rooflines.
New attic spaces across Tempe, from rebuilt rooflines on older homes to attics in new subdivision construction, get full depth insulation installed to current code. We set baffles for proper attic ventilation and leave it ready for inspection before drywall goes up.
Exterior wall framing on new Tempe construction and garage or room conversions gets fiberglass batts cut to fit stud bays without gaps or compression. We insulate around outlets, plumbing, and framing irregularities so the full wall cavity reaches its rated performance.
Blown in cellulose or fiberglass fills new attic framing evenly, reaching tight corners and irregular joist spacing that batts can miss. We use it on new truss systems in Tempe subdivisions and on rebuilt rooflines where the framing layout is not a standard grid.
As a licensed general contractor, Tycho Solutions installs insulation as part of full builds, additions, and renovation projects across Tempe, coordinating with our own roofing, framing, and HVAC crews under ROC 364735. One point of contact covers the entire building envelope.
Additions and attic rebuilds on Tempe’s older homes often start with clearing out old, degraded insulation before new material goes in. We remove the existing batts or loose fill, check the framing underneath, and install fresh insulation to current standards as part of the build.
Builders bring Tycho onto Tempe projects because insulation goes in as part of the same schedule as framing and roofing, coordinated by one licensed contractor instead of handed off between trades. Homeowners get the same coordination on additions and rebuilds, with a written workmanship warranty backing the install.
Every install comes with a written workmanship warranty, backed by manufacturer coverage on the insulation material itself.
One Tycho crew and one schedule cover insulation alongside roofing, framing, or remodel work on the same Tempe project.
We install spray foam, batts, and blown-in fill sized to Tempe’s attic heat load, not a one size fits all depth.
Tycho carries Arizona ROC #364735, fully licensed, bonded, and insured for insulation work across Tempe.
Tempe’s housing stock splits fairly cleanly into two eras. Original ASU-adjacent bungalows and ranch homes from the 1960s through 1980s carry small, low-clearance attics with original ductwork snaking through settled insulation, while master-planned construction pushes attics with taller trusses and room for full-depth blown-in fill. Additions, garage conversions, and second-story pop-tops on the older stock routinely get built with no wall insulation at all, since the original framing never called for it.
The failure point is almost always the attic floor plane, not the walls. Original batts compress and settle over decades, dropping well below their rated depth, and gaps around can lights, plumbing stacks, and attic hatches let conditioned air leak straight into the attic. On tile and foam flat roofs especially, radiant heat driven through the roof deck finds that thin or gapped insulation and pours straight into the living space below, which is why attic floor depth and radiant barrier condition matter more here than in milder climates.
HOA and municipal design rules across Tempe generally restrict visible roof mounted vents and turbines, so insulation upgrades have to work with the roofline that already exists rather than adding new penetrations. That pushes more of the performance burden onto attic floor depth, baffle placement, and radiant barrier, since ventilation changes are rarely an option.
By submitting this form, you agree to receive communications from Tycho Solutions. We respect your privacy.
Tycho holds Arizona ROC #364735, fully licensed, bonded, and insured for insulation work across Tempe.
We install insulation as part of full builds, additions, and rebuilds, not a standalone patch job.
Insulation schedules alongside our own roofing, framing, and remodel crews on new Tempe construction.
Insulation work is scheduled and priced up front, so your project stays on time and on budget.
Cost depends on attic or wall square footage, the material you choose, spray foam, blown-in, or batt, and how easy the space is to access. An older attic with settled insulation and existing ductwork takes more labor than an open new construction attic.
We walk the space, measure square footage and current depth, and put a written quote in front of you before any work starts.
It depends on condition, not age alone. If the batts are dry, intact, and just thin, adding blown-in on top of existing batts to reach current depth is a reasonable fix.
If insulation is compressed to almost nothing, contaminated by rodents, or water stained from a past roof leak, topping it off just buries the problem. At that point we pull it out and start with a clean attic floor.
Yes. Flat and low-slope roofs common on Tempe’s foam and built-up systems don’t have the attic airspace a pitched roof gives you, so insulation often goes into the roof assembly itself as rigid board or spray foam rather than loose fill on an attic floor.
Pitched roofs with real attic space use blown-in or batts at the floor instead, with baffles to keep soffit vents clear.
Yes. Radiant barrier goes up on the underside of the roof deck or across the top of the attic floor, reflecting radiant heat back out before it reaches your insulation or ductwork.
It works alongside blown-in or batt insulation rather than replacing it, and it matters most on tile and foam roofs where the roof deck runs hot most of the year.
Yes. As a licensed general contractor, we install insulation on commercial builds and tenant improvements across Tempe alongside our roofing and construction crews, coordinating directly with property managers, architects, and other trades on the job.
Commercial work typically means larger open attic or plenum spaces and code-driven R-value targets, which we scope during a site walk before quoting.
Tycho Solutions holds Arizona ROC #364735 and is fully licensed, bonded, and insured for insulation, construction, and remodel work in Tempe.
Insulation itself typically doesn’t need a standalone permit, but when it’s part of a larger addition, garage conversion, or rebuild, we pull whatever permits the City of Tempe requires as part of that project and handle the inspection process.
