Tycho Solutions handles roofing company in Tempe, AZ, plus new construction roofing. Complete systems installed to the deck, not patched.
Tempe’s housing stock splits into two eras, and each one fails differently. Mid-century tract homes carry original concrete and clay tile on moderate pitches, and the tile itself usually outlasts the roof: what actually fails is the underlayment underneath it, baked brittle by decades of attic heat until it cracks at the valleys and pipe boots.
Newer infill near the university core runs flatter and lower-slope, where the failure point shifts to the foam or elastomeric coating itself. Ponding water at low spots and UV-cracked membrane seams do the damage there, not wind or hail, and a soft deck under either roof type means the whole system needs attention, not a patch.
We tear failing roof systems down to the deck and rebuild them for Tempe’s heat and monsoon cycles, not patch around problems for one more season.
We walk the roof, photograph what we find, and tell you whether it needs replacing now or has time left.
From new build infill near the city’s core to full roof replacements on Tempe’s established mid-century homes, our crews install tile, foam, metal, and shingle roofing systems built for Arizona’s heat and monsoon storms.
Tempe’s roofing work ranges from single custom homes to multi-family and commercial buildings tied to the city’s ongoing infill development near the university corridor. We install complete systems from the ground up, coordinating with builders on plan review, material selection, and job site scheduling from start to finish.
Many Tempe roofs date to the city’s mid-century growth years and are reaching the end of their service life. We tear off the old system down to the deck, correct any damaged sheathing, and install a new roofing system built to handle Arizona’s UV load and monsoon rainfall.
Tempe’s flat-roof homes and additions, common in the city’s newer infill construction, call for spray polyurethane foam over a traditional shingle or tile system. We apply the foam directly to the roof deck and finish with an elastomeric coating, sloped to move water off the roof during monsoon storms.
Standing seam metal fits the contemporary infill homes and custom builds going up around Tempe’s core, where owners want a sharper architectural look than a traditional pitched roof. Panels are installed with concealed fasteners and a heat-reflective finish that helps push back against direct desert sun.
Established Tempe neighborhoods built during the city’s mid-century expansion carry a lot of original concrete and clay tile, and those roofs are due for full replacement rather than patch repairs. We remove the old tile, install fresh double underlayment and battens, and reset the tile for proper drainage.
Tempe’s pitched-roof tract homes, many built before the city’s newer infill wave, are common candidates for full shingle replacement once the original roof reaches the end of its service life. We strip the old shingles, correct ventilation, and install a new architectural shingle system rated for Arizona wind.
Builders working infill lots near the university core and homeowners replacing original mid-century tile both need a crew that treats the roof as one system, deck, underlayment, flashing, and covering together, rather than a quick swap of the top layer over a deck nobody inspected.
Every tear-off comes with a written warranty on materials and workmanship, so a monsoon season that would expose a patch job doesn’t leave you covering the bill.
One crew manages tear-off, deck repair, and install in sequence, so a Tempe roof isn’t sitting open under a summer storm cell for days at a time.
We spec tile, foam, metal, and shingle systems rated for sustained triple-digit heat, not the lighter-duty products built for milder climates.
Tempe’s housing stock splits into two distinct eras, each calling for a different roofing approach. Neighborhoods from the city’s mid-century growth carry concrete and clay tile on moderate pitches, while newer infill near the university core leans toward flat and low-slope construction on tighter lots. There is no single default roof here, so we start with build era and slope, not the finished product.
On the older tile stock, the tile itself usually outlasts the roof. What fails first is the underlayment beneath it: years of attic heat past 150 degrees dry out the felt or synthetic layer until it cracks, and monsoon rain finds those cracks at valleys, hips, and pipe boots. On flat and low-slope roofs, the foam or elastomeric coating takes the sun’s UV load directly, so chalking, hairline cracking, and ponding at low points are the signs to watch, not one obvious leak.
Design review in Tempe’s established communities generally holds tile roofs to their original profile and color range, which narrows a full tile replacement to matching tile rather than switching systems. Newer infill and commercial buildings carry more latitude, which is usually where standing seam metal or a foam system gets specified from the start. Either way, we confirm what the property’s design rules allow before we finalize a material.
By submitting this form, you agree to receive communications from Tycho Solutions. We respect your privacy.
Fully licensed, bonded, and insured under Arizona ROC #364735 for every roofing project we take on in Tempe.
We tear off the entire roof system rather than layering new material over a deck we haven’t inspected.
Materials and installation methods chosen for sustained Arizona heat and monsoon wind, not a milder climate’s roofing standard.
One crew runs your project start to finish, so a Tempe roof replacement stays on schedule and on budget.
Cost depends on roof size, pitch, material, and how much of the deck needs correction once we open up the old system, so we don’t quote a number sight unseen. What we can tell you is that a full replacement, done once and done right, almost always costs less over the life of the roof than a string of patch repairs on an old tile or shingle system that’s already past its service life. We walk the roof and give you a written, itemized quote before any work starts.
On most trades a repair is the right first move, but roofing is different, especially on an old tile or shingle system. Patching failing underlayment usually buys one more monsoon season at best, because the material around the patch is aging at the same rate as the section you just fixed. We’ll give you the honest read on whether a repair still makes sense, but on a roof past its service life, a full replacement is almost always the call that avoids a second, larger repair bill a year later.
Yes. A lot of Tempe’s newer infill and commercial buildings use flat or low-slope roofs, and those systems fail differently than a pitched tile or shingle roof: ponding water, UV-cracked coatings, and membrane seams that split at the edges rather than an obvious missing shingle. A flat roof replacement in Tempe usually means removing the old foam or membrane down to the deck, correcting slope so water actually drains to the scuppers, and rebuilding with a system rated for sustained heat rather than a quick recoat.
Yes, we work as a commercial roofing contractor in Tempe on everything from multi-family buildings to standalone commercial construction, most of it TPO, PVC, or built-up roofing on a low-slope deck. Commercial work runs on tighter timelines and stricter code requirements than a single-family re-roof, so we coordinate directly with property managers and general contractors on sequencing, inspections, and permitting rather than treating it like a residential job at a larger scale.
Yes. Tycho Solutions is licensed, bonded, and insured under Arizona ROC #364735, and we pull the required City of Tempe building permit ourselves on every full roof replacement rather than leaving that step to the homeowner. Permitting on a re-roof typically covers the scope of work, the underlayment and material specs, and a final inspection before the job closes out, and we handle that inspection scheduling as part of the project.
Most single-family tile or shingle replacements run two to five days once the crew is on site, longer if we find damaged decking underneath that needs to be replaced before the new system goes down. Foam and flat roofing on a low-slope commercial or infill building can move faster since there’s no tile to strip and reset, but summer scheduling around monsoon storm windows can add a day or two either way. We’ll give you a real timeline once we’ve seen the roof.
