Tycho Solutions handles ac installation in Gilbert, AZ, on new construction and whole-system replacement. Sized to the house, installed complete, never patched.
Most Gilbert homes fall into two build eras: production tract construction from the 1990s through the mid 2000s, and newer all electric infill going up since 2015. The older stock runs original ductwork and a condenser well past its service life, and summer days over 110 degrees keep that equipment cycling at close to full duty for months.
That kind of sustained run time is usually what ends a compressor, not one bad afternoon, so replacement tends to follow a slow drop in cooling capacity rather than a sudden failure. Swapping in a correctly sized system means matching the indoor coil, refrigerant type and duct capacity to the new outdoor unit, since mismatched components are the most common cause of a Gilbert system that still runs hot upstairs.
From ground up new builds to full system replacements, we design and install cooling, heating and ductwork for Gilbert homes and commercial properties.
We run a load calculation for your home or building before we quote equipment, not a square footage rule of thumb.
Gilbert’s newer subdivisions run mostly slab on grade, single story production homes with condensers set in side yards under HOA screening rules. We size the unit to the home’s actual load, place it to meet those visibility standards, and commission it before handoff.
Gilbert’s mild winters still bring cold mornings at its elevation, and many production homes on gas service pair a furnace with the cooling system for that stretch of the year. We install the furnace as part of the same air handler setup, matched to the ductwork already in place.
As Gilbert homeowners convert garages into offices, gyms or casitas, those rooms sit outside the reach of the main duct run. A ductless mini split cools or heats the space directly without opening walls or extending trunk lines through finished areas.
New Gilbert construction now goes up under tighter energy codes, with better window ratings and insulation than homes built even a decade ago. We run full Manual J, D and S calculations against those plans so the whole system, not just the condenser, is sized correctly from day one.
Some of Gilbert’s newest developments are built all electric with no gas line to the house, which rules out a traditional furnace. A heat pump handles both sides of the year off one outdoor unit, a fit for that construction and for homeowners standardizing on electric.
In Gilbert’s single story tract homes, supply and return runs live almost entirely in the attic, exposed to extreme summer heat gain. We fabricate and install that ductwork during the rough in phase, seal every joint, and size returns so airflow reaches rooms furthest from the air handler.
Builders and homeowners here work with us because one crew handles the equipment, the ductwork and the electrical tie in on the same schedule, licensed under one contract instead of three separate trades passing blame back and forth when something doesn’t line up.
Our installs carry manufacturer and workmanship coverage that holds up through a Gilbert summer, when a system runs harder and longer than anywhere else in the Valley.
We install equipment sized to the home’s real load, not the smallest unit that fits the budget, using ductwork rated for Gilbert’s attic temperatures.
One point of contact coordinates equipment delivery, rough in and startup with your builder’s schedule, so HVAC never becomes the trade holding up a Gilbert closing.
Gilbert’s housing stock splits fairly cleanly by decade. Homes from the tract boom of the 1990s and early 2000s were built to a lighter energy code, with less attic insulation and older window ratings, so the HVAC system carries more of the cooling load than it would in a newer build. Homes going up now, many all electric with no gas line to the property, ask a heat pump to cover both sides of the year off one outdoor unit.
The part of the system that actually fails first in Gilbert is rarely the compressor. It’s the ductwork sitting in an attic that regularly tops 140 degrees in July, where flex duct insulation degrades, mastic joints dry and separate, and an undersized return starves the system of airflow. A new condenser tied into leaky old ductwork will never deliver its rated capacity, so we treat the duct run as part of the installation, not an afterthought.
Gilbert’s design guidelines generally keep condensers and any ductless outdoor unit screened behind a wall or approved fence rather than visible from the street, which limits where equipment can sit and how large a footprint it can have. That constraint shapes what we spec as much as the load calculation does, especially on smaller lots with less room to work with.
By submitting this form, you agree to receive communications from Tycho Solutions. We respect your privacy.
Tycho Solutions holds Arizona ROC #364735, fully bonded and insured for HVAC installation on homes and commercial properties across Gilbert.
We calculate real cooling and heating load room by room instead of guessing off square footage alone.
Equipment, ductwork, electrical tie in and startup all come from one crew on one schedule, not three separate subcontractors.
We schedule HVAC work around your build timeline and hold to the quote we give, with no surprise change orders.
Cost depends on the tonnage your home actually needs, whether we’re replacing a straight swap or upsizing ductwork for a bigger system, and whether the job is a single condenser or a full furnace and coil pairing. We size the system to your home’s real load first and give you a written quote before any work starts, rather than a phone estimate based on square footage.
If the compressor or coil has failed on a unit already past 12 to 15 years old, repair usually buys you a few more months before the next failure, often in the middle of summer when Gilbert’s heat gives you the least room to wait. Once a system is at that age we’ll tell you honestly if repair makes sense or if replacement is the better use of the same money.
Yes. Commercial hvac installation in Gilbert is often a rooftop package unit set on a flat or low slope roof rather than a ground mounted condenser, which changes how we handle curb flashing, condensate drainage and roof penetrations. We coordinate that work with the roofing trade so the curb is sealed correctly the first time, since a leaking curb shows up as a ceiling stain, not an HVAC complaint.
Yes. Tycho Solutions is licensed under Arizona ROC #364735, and Gilbert requires a permit and inspection for HVAC change outs and new installs, not just new construction. We pull that permit as part of the job and schedule the town’s inspection around your install, so the paperwork is handled before we’re back in the truck.
New construction hvac in Gilbert is a full system build from the ground up: duct design and rough in before drywall, Manual J and Manual D calculations against the plan set, and equipment set and startup at trim. We work directly with the builder’s schedule so HVAC isn’t the trade holding up a certificate of occupancy.
We run a room by room load calculation using your home’s orientation, window area, insulation and duct condition, not just square footage. A unit that’s too big cools the air fast and shuts off before it pulls humidity out, and a unit that’s too small runs constantly and still can’t keep up on the hottest days, so getting the number right matters more here than almost anywhere in the state.
